EBC Brake Pads for Bikes – GPFAX491HH Grand Prix – (1 Set)
Kindly contact us at +91-7697258886, +91-7869912321 to confirm availability before placing order
If you face any issue while placing orders.
Kindly give us a Call/Whatsapp at-
+91 9424014762 / +91 9860529838.
Out of stock
Finance Facility Available. For any assistance contact us
NO COST EMI for 3 Months Available on Credit Cards, Simpl, Zest Money
Fitment and compatibility
- Triumph Daytona 675 (13-17)
About this product
GPFAX is the new compound that replaces GPFA.
- ONLY FOR RACE USE.
- The highest performance friction level is known.
- NOT R90 street legal or TÜV tested.
- Guaranteed lifetime performance.
GPFAX Sintered Road Race Brake Pads have by far the highest known friction with a measurement between 0.6 and 0.7 and deliver the most amazing brake effect. Because of this factor, they are unsuitable for street use or for road tires.
Zero brake fade is guaranteed and the heat stability of these brake pads is perfect leaving the racer with high confidence and a product that can be used over numerous races.
GPFAX Sintered Road Race brake pads are a closed circuit use pad only and street/highway riding with this material is highly inadvisable and dangerous.
Such high friction levels as delivered by these pads are for ideal track conditions with race tires or slicks on prepared asphalt surfaces and NOT for use with highway tires or on the highway.
This material is not ECE R 90 approved nor TUV tested with a German ABE and use on the highway is, therefore, illegal in many countries.
The material quickly builds from an initial friction level of 0.6 (which in itself is a massive brake friction level rarely achieved by any competitor material) up to a huge 0.7 with a minimum in-stop friction level of 0.65.
This tiny fall off from 07 – 0.65 during braking would be almost undetectable by the rider allowing superb brake feedback and control at the lever and allowing feathering of the brake predictably and steadily throughout deceleration.
The new material also wears better and causes lower rotor/disc damage than previous materials and should be good for 4-5 race events of a typical 20-25 lap duration minimum.
Pads should be discarded when less than 2.5 mm of friction material remains to avoid fluid vapor lock due to excess piston fluid volume.
This material contains no toxic lead nickel or zinc which is a trick used by our competitors to ramp up friction levels the cheap way.
Preparing your Race discs/rotors before using this Compound.
Many pads contain carbon particles some in high percentages and this leaves a grey glaze on rotors.
This MUST be removed by fine abrasive paper or what is known as a Scratch Pad in the USA.
Take care not to promote deep scratches on the rotor which will cause prolonged bedtimes.
Bedding in your new brake pads
After installing the pads ride the bike for 2 laps very gently applying the brakes well in advance of where you wish to stop at speeds not exceeding 80 MPH.
Proceed a further 2-3 laps gradually increasing the brake load until you feel the pads become stable and predictable.
Bedding into worn or distorted discs/rotors will be dramatically longer.
Inspect pads every Race for wear on EACH pad and replace when any single pad is down to 2.5 mm or the lever becomes spongy.
Different brake systems respond differently and have differing amounts of fluid in their piston chambers and the time for an ideal replacement of the pads due to loss of brake feel can only be assessed by the individual rider and bike.
Brake fluid considerations
Old brake fluid affects the sponge and brake feel. Most brake fluids are Glycol based and over time their hygroscopic nature means they will absorb moisture even through the brake lines.
As amazing as this sounds it does happen and fluids can contain as much as 12% water by volume in worst cases.
It is highly advised to replace brake fluid every 6-8 race events as a minimum with a high wet boiling point fluid such as Maxima Race fluid.
Use only fluids from a sealed container, never from a bulk can or drum as in this storage condition the fluid will act like an old material even before you use it having absorbed water since originally opened.
Brake discs/Rotors for race use needed
COD conditions: Place your order selecting Offline Payment mode then pay ₹1000/- advance for COD order confirmation through UPI / Credit Card / Debit Card by contacting our sales team at +91-7697258886 / 7869912321.
Extra Charges for COD Service will be applicable as charged by Shipping partner (Minimum 200 Rs or 3% of the bill amount).
Bill amount should be minimum 3000 Rs. to process COD order.