Viaterra Fender – Daily Use Motorcycle Glove – Green

1. Constructed using perforated stretch textile & mesh material on the back and micro suede on the palm to improve dexterity and comfort.

2. The knuckles are protected by hard plastic protectors with EVA padding.

3. The index and thumb finger tips are touch screen sensitive.

STEP 1 – 

Measure your hand using a tailor’s tape measure There are two key measurements that you need to take into consideration for figuring out your glove size.

A) Circumference –

Wrap the tape measure around your palm at its widest point and lightly close your hand before taking the measurement.

B) Length – Measure from the tip of the middle finger to the base of your palm at your wrist.

STEP 2 –

Find your glove size by checking hand measurements against the chart provided – If both the measurements do not fall in one particular size – use the larger of the two measures to choose the glove size. – If the two measurements are on the border line between two sizes, try both the sizes and choose the one that offers a better fit.

STEP 1 –

Confirm that the gloves are a comfortable fit. They should not be excessively tight on all fingers (including the thumb) & knuckles. To check this, try the gloves on and form a fist several times and verify if:

1. Adequate room for all fingers (specially thumb) to move and operate controls comfortably.

2. Check the fitment on both hands since your left and right hand sizes do vary. Ensure that the fit on first try is not so tight as to cause discomfort and/or restrict movement

STEP 2 –

Ensure the knuckle protectors are properly positioned.

The way to check this is:

1. Roll your hand into a tight fist and hold the position for 5-10 minutes. This position should be easy to hold without causing any discomfort or causing any stress points.

2. Ensure that the edge of the knuckle protector is not over the knuckle when the fist is formed.

The Fender gloves are designed primarily as daily use gloves for the urban commute. These will not offer the same level of on-road protection as our street gloves. Because these gloves are built primarily from textile & mesh materials to offer comfort & ventilation, they will wear out faster than traditional leather gloves, depending on usage & care taken.

This wear is entirely dependent upon individual use and will not be covered under the warranty policy . Since the gloves are used in the urban environment, depending on local conditions, they will get dirty. If this is a concern, we recommend cleaning the gloves after each ride.

Fit and comfort are subjective matters and will vary from person to person. We recommend trying out the gloves before finalizing the purchase. Do not let the hard Velcro come in contact with the fabric of the gloves, which will make the fabric fray off.

Materials needed: 

Microfiber/ soft cloth Small bowl or mixing cup Absorbent towels Soft-bristled brush Diluted cleaning solution Lukewarm water

How to clean & dry gloves?

1. Clean the gloves as soon as you are able to, after your off-road session. This will make removing any stains easier. Leaving the gloves un-clean will make removing any stains tougher.

2. In a small bowl or measuring cup, mix a portion of diluted cleaning solution in lukewarm water.

3. Dampen a microfiber cloth with the mixture and gently wipe the stained areas. If there are stains which you are unable to remove using a damp cloth, use a soft bristled brush soaked in a mild pH neutral soap and rinse off using cold water. Please note that using a brush could lead to piling which will not be covered under warranty.

4. Clean the gloves starting at the wrist and working toward each fingertip. Be sure to clean well between each finger. Keep moving to a clean area of the cloth as the dirt is transferred.

5. Rinse the cloth often as the dirt is transferred. Turn the gloves over and repeat on the other side.

6. DO NOT USE HOT WATER

7. Do not use detergents, fabric stain removers, bleach or any chemicals for cleaning.

8. Do not wash the gloves in a washing machine.

9. Dip dry the gloves after cleaning in a ventilated area away from direct sunlight.

10. Do not wring the gloves.

How to store? 

When gloves are stored wet or in a non-ventilated area, this may cause deformations and ruin your gloves, not to mention this allows mildew to grow on the leather causing discoloration and damage.

1. Make sure that your gloves are completely dry before you store them.

2. Place them in a breathable cotton bag to protect them from dust but with enough air circulation to prevent mildew from forming.

3. Store them in a cool, dry, well ventilated area

Warranty 

We offer a 6 month warranty on manufacturing and material defects. Our gloves are made in the same factories that manufacture for top brands like Dainese, Alpinestars, Furygan, Rev’It, etc. Please click here for details.

Repairs 

Minor repairs of opened stitches, Velcro etc. due to normal wear and tear can be done at a reasonable charge. Send us an email with pictures so we can determine if the gloves can be repaired or not. Please click here for details.